D-Link DVG-1402S and Broadvoice - Please help me configure!...

[yorktown48]

I am trying to set up quite a few D-Link DVG-1402S routers with Broadvoice. I see some people are able to get it working but I have not seen info on the config.

Here's my admin panel on the D-Link.
I have linked screen shots so you can see them as well.

PLEASE LET ME KNOW WHAT TO SET SO I CAN CONFIGURE THIS ASAP. THANKS!

-----------------------------
TELEPHONY CONFIG MENU
-----------------------------
Screen Shot

ToS
Signaling ToS ===> 0
RTP ToS ===> 0

Receive Gain ====> -3 db
Transmission Gain ====> -11 db

DTMF Relay ====> RFC2833
TEL Dial Signal ====> AUTO

Echo Cancel ====> ENABLED
VAD ====> ENABLED
Digital Timer ====> 4 sec

Call Waiting Alert Tone ====> ENABLED

-------------------------
SERVER CONFIG MENU
-------------------------
Screen Shot

Server FQDN ====> ENABLED
IP Address ====> 0. 0. 0. 0
Domain Name ====> proxy.atl.broadvoice.com
Port ====> 5060
Service Domain ====> sip.broadvoice.com
URL Format ====> SIP-URL
User Parameter Phone ====> DISABLED
Caller ID Delivery ====> YES
Display CID ====> ENABLED
Timer T2 ====> 4 sec

Initial Unregister ====> DISABLED
Register Expiration ====> 3600 sec
Session Expires ====> 180 sec
Min-SE ====> 180 sec
Session Expires Refresher ====> UAC

Outbound Proxy ====> ENABLED
Outbound Proxy IP ====> 147.135.28.128 (this is proxy.atl.broadvoice.com)
Outbound Proxy Port ====> 5060

Codec Priority & Packet Interval
G.711a-law ====> 1st 20 ms
G.711u-law ====> 2nd 20 ms
G.723.1 ====> 5th 30 ms
G.729a ====> 3rd 20 ms
G.726 ====> 4th 20 ms


---------------------
STUN Configuration
---------------------
Screen Shot

STUN State ====> DISABLED
STUN Server IP Address ====> 0 .0 .0 .0
STUN Server Port ====> 6355
STUN ReqInterval ====> 60 sec
STUN NAT Type UnKnown

Index SIP Message socket mapped ip/port SIP RTP socket mapped ip/port
1 0.0.0.0 : 0 0.0.0.0 : 0
2 0.0.0.0 : 0 0.0.0.0 : 0


------------------------------
SIP Configuration - User Agent
------------------------------
Screen Shot


Same Phone Number ====> DISABLED
Index ====> 1
Phone Number ====> BROADVOICE TEL # (No DASHES or Spaces) ex: 2125551212
Display Name ====>
User Agent Port ====> 5060
Authentication Username ====> BROADVOICE TEL # (No DASHES or Spaces) ex: 2125551212
Authentication Password ====> BROADVOICE Auth Password ex: CVgXX123ffeXX
Confirm Password ====> BROADVOICE Auth Password ex: CVgXX123ffeXX

Query Registeration State

-------------------
SIP - Peer to Peer
-------------------
Screen Shot

Index Phone Number User IP Address Port Edit
1 @ 0.0.0.0 5060
2 @ 0.0.0.0 5060
3 @ 0.0.0.0 5060
4 @ 0.0.0.0 5060
5 @ 0.0.0.0 5060
6 @ 0.0.0.0 5060
7 @ 0.0.0.0 5060
8 @ 0.0.0.0 5060
9 @ 0.0.0.0 5060
0 @ 0.0.0.0 5060

---------------------
Plug'N Dial Provision
---------------------
Screen Shot

Plug'N Dial Server Address
Software Update Mode ====> TFTP (Can Not Change this)
Server FQDN ====> ENABLED
Server Address ====> 0 .0 .0 .0
Domain Name ====> proxy.atl.broadvoice.com
Server Port ====> 69


Update Configuration
Plug'N Dial ====> DISABLED
Plug'N Dial ====> [RESET]
Last Update Status


Again.... Please any help on configuring this is appreciated. I tried changing all the ports to 5060. I played with the server (sip.broadvoice.com, proxy-atl.broadvoice.com, proxy.atl.broadvoice.com). I also played with items that were disabled and tried to enable them. I also tried to register the device on the User page....either I would get "Error Code" or "Communicating with Server" and it would hang.