How to setup Linksys Phone Adapter SPA1001 for braintel

[fak06]

Hello all,

I have just bought a new Linksys phone adapter. Would it be possible for some one to help me in seting it up. I need the setup instructions. Any help would be greatly appreciated.

[mirza001]

I posted this configuration here and at BrainTEL forums and it's still valid, I have slightly modified the dial plan for better performance and it also includes the support of using sipbroker with you phone:

(BRAINTEL VOIP SERVICE)http://forum.voxilla.com/braintel-users-group/braintel-voip-service-14513-5.html

BrainTel Configuration for Sipura/Linksys ATA’s

All these settings are testing and working 100% for BrainTEL;
when you are using router it does not matter if you have static IP or dynamic IP from your ISP because your router is taking care of your internal IP addresses through its DHCP configuration.

For SPA 1001 you can use the line 1 or line 2.

Connect ATA to router then connect a normal phone to any out put port on it (indicated by line 1 or 2), on this phone pick up the handset and press * (star) key four times, you will hear the message of “Configuration menu……” press 110 followed by the # key, it will announce the IP address of your ATA. (Suppose its 192.168.x.x or 10.0.x.x)

On the computer, which must be connected to the same router, open up IE (browser) and in the address bar enter the IP address of your ATA (192.168.x.x or 10.0.x.x) and press enter. It will open up the web configuration page; you will have to click on Admin logon on the right hand side top and then in the middle click on Advanced view:

1. Under System
Change DNS Server order: DHCP, Manual
Primary NTP server: pool.ntp.org
Secondary NTP server: time.nist.gov

2. Click SIP on the Configuration Menu
Go to NAT Support Parameters
For Substitute VIA Addr: Yes
For Send Resp To Src Port: Yes
For STUN Enable: Yes
For STUN Server: stun.fwdnet.net
(Any STUN server can be used they all work the same)
Change NAT Keep Alive Intvl: 30

3. Click Provisioning on the Configuration Menu
Go to Configuration Profile
Change Provision Enable: No

4. Click Regional on the top:
Under Ring and Call Waiting Tone Spec
Change Ring Waveform to Sinusoid
Change Ring Voltage: 90
Change Ring Frequency: 20

Under Miscellaneous
Change Time Zone to your zone

5. Click Line 1 for phone 1 on the Configuration Menu

Go to NAT Support Parameters
Next to NAT Mapping Enable: Yes
Next to NAT Keep Alive Enable: Yes

Go to SIP Settings
Next to SIP Port: 8891

Go to Proxy and Registration
Next to SIP Proxy: 83.138.152.36:8891 or chat.brain.net.pk:8891
Next to Register: Yes
Next to Register Expires: 120
Next to Use OB Proxy In Dialog: No
Next to Make Call Without Reg: No
Next to Answer Call Without Reg: No

Go to Subscriber Information
Next to Display Name: Your Name
Next to User ID: Your BrainTEL phone number
Next to Password: Your BrainTEL password
Next to Use Auth ID: No

Go to Audio Configuration
For Preferred Codec: G729a
For Use Pref Codec only: No

Go to Dial Plan
Next to Dial Plan: (*xx|[2-9]xxxxxx|<42:042>[2-9]xxxxxx|1x.|03xxxxxxxxx|02xxxxxxxx|02xx11x.|0 [4-9]xxxxxxxx|0[4-9]xx11x.|<555:2100800>|<**:*>[x*].<:@sipbroker.com>)

6. Click User 1 on the Configuration Menu
VMWI Ring Splash Len: 0

7. Click the Save Settings button to save your changes.

[fak06]

Thank you so much for your help mirza. Really appreciate it.