BrainTel settings for Sipura/Linksys ATA’s

[mirza001]

All these settings are testing and working 100% for BrainTEL;
when you are using router it does not matter if you have static IP or dynamic IP from your ISP because your router is taking care of your internal IP addresses through its DHCP configuration.

Connect ATA (Spa 2000 or PAP2-NA or PAP2T-NA) to router then connect a normal phone to any out put port on it (indicated by line 1 or 2), on this phone pick up the handset and press * (star) key four times, you will hear the message of “Configuration menu……” press 110 followed by the # key, it will announce the IP address of your ATA. (Suppose its 192.168.x.x or 10.0.x.x)

On the computer, which must be connected to the same router, open up IE (browser) and in the address bar enter the IP address of your ATA (192.168.x.x or 10.0.x.x) and press enter. It will open up the web configuration page; you will have to click on Admin logon on the right hand side top and then in the middle click on Advanced view:

1. Under System
Change DNS Server order: DHCP, Manual
Primary NTP server: pool.ntp.org
Secondary NTP server: time.nist.gov

2. Click SIP on the Configuration Menu
Go to NAT Support Parameters
For Substitute VIA Addr: Yes
For Send Resp To Src Port: Yes
For STUN Enable: Yes
For STUN Server: stun.fwdnet.net
(Any STUN server can be used they all work the same)
Change NAT Keep Alive Intvl: 30

3. Click Provisioning on the Configuration Menu
Go to Configuration Profile
Change Provision Enable: No

4. Click Regional on the top:
Under Ring and Call Waiting Tone Spec
Change Ring Waveform to Sinusoid
Change Ring Voltage: 90
Change Ring Frequency: 20

Under Miscellaneous
Change Time Zone to your zone

5. Click Line 1 for phone 1 on the Configuration Menu

Go to NAT Support Parameters
Next to NAT Mapping Enable: Yes
Next to NAT Keep Alive Enable: Yes

Go to SIP Settings
Next to SIP Port: 8891

Go to Proxy and Registration
Next to SIP Proxy: 83.138.152.36:8891 or chat.brain.net.pk:8891
Next to Register: Yes
Next to Register Expires: 100
Next to Use OB Proxy In Dialog: No
Next to Make Call Without Reg: No
Next to Answer Call Without Reg: No

Go to Subscriber Information
Next to Display Name: Your Name
Next to User ID: Your BrainTEL phone number
Next to Password: Your BrainTEL password
Next to Use Auth ID: No

Go to Audio Configuration
For Preferred Codec: G729a
For Use Pref Codec only: No

Go to Dial Plan
Next to Dial Plan: L:20,S:7,(*xx|[2-9]xxxxxxS0|<42:042>[2-9]xxxxxxS0|1x.|03xxxxxxxxxS0|02xxxxxxxxS0|02xx11x.|0 [4-9]xxxxxxxxS0|0[4-9]xx11x.|<555:2100800>S0|<**:*>[x*].<:@sipbroker.com>)

6. Click User 1 on the Configuration Menu
VMWI Ring Splash Len: 0

7. Click the Save Settings button to save your changes.

[mirza001]

Correct Dial Plan for Sipura/Linksys ATA’s:

L:20,S:7,(*xx|[2-9]xxxxxxS0|<42:042>[2-9]xxxxxxS0|1x.|03xxxxxxxxxS0|02xxxxxxxxS0|02xx11x.|0[4-9]xxxxxxxxS0|0[4-9]xx11x.|<555:2100800>S0|<**:*>[x*].<:@sipbroker.com>)

[hkalltheway]

Mirza bhai, I was wondering if you know how to set up voicemail tone...When I receive a new voicemail, I get an e-mail, but no stutter dialtone or message waiting indicator on my phone...generally in canada, when there is a voicemail waiting, you can hear a stutter tone with a voicemail indicator flashing. Does brain support this? On their site, it says that they support voicemail tone in hard setup and not in soft setup..Any information on this sir? thanks

[mirza001]

You are lucky that you are getting e-mail for voice messages, lot of other users including me are dying to have this feature again!

It used to work fine (shutter tone for VM on ATA, indication on soft phone, e-mail for messages) till May 2006 and then the SIP server was relocated and all wonderful features were snatched from users; only VoIP service was restarted with G729 codec.

If you check BrainTEL forums and BrainTEL section (The site appears and diapers magically) you will see every one has been asking for these features and had suggested so many other good suggestions but.....

[QAZI SAEED]

Dear Mirza I am not being able to find the configuration of Linksys/Sipura 3102. I have already purchased the SPA 3102 ( Gateway + Router). The configuration seems to be quite different from SPA 3000. I am registered in Braintel as PQAZI. Can u please send me the braintel configuration for 3102. I will be much obliged.
P QAZI

[k2man]

Originally Posted by QAZI SAEED

Dear Mirza I am not being able to find the configuration of Linksys/Sipura 3102. I have already purchased the SPA3102 ( Gateway + Router). The configuration seems to be quite different from SPA 3000. I am registered in Braintel as PQAZI. Can u please send me the braintel configuration for 3102. I will be much obliged.
P QAZI

Qazi,
Mirza doesn't work for braintel and he would have no knowledge of your account. But he is very knowledgeable in things SIP related. What may help him and other is if you took screenshouts of the configuration pages and posted them here. also look to see if there is a advanced but make sure you take screen shots in Admin and advanced mode.

[mirza001]

Originally Posted by QAZI SAEED

.....the configuration of Linksys/Sipura 3102. I have already purchased the SPA3102 ( Gateway + Router). The configuration seems to be quite different from SPA 3000.....

Spa 3000 & 3102 have so many configurations and it’s not possible to create a general setup file for it, these ATA’s have to be custom configured according to each user requirements.

I have tried to create basic configuration for SPA3102 in this file (get file from this
Link) and hope this will help the users, you may observe under the “VoIP Fallback To PSTN” and under “SIP Settings” the SIP port is 5060. I would encourage the users of SPA3102 to share their experience.

Also under “Miscellaneous” you can adjust the Time zone to yours and adjust “Caller ID Method” to “Bellcore(N.Amer,China).